Frustrated by a Faulty Garage Door Spring?

Is your garage door stuck or not closing properly? It could be due to a faulty spring, a common issue that disrupts daily life in West Lake TX. — Schedule your spring repair now.

A broken spring renders your garage door dead weight, trapping your vehicle inside or leaving your home vulnerable to security risks. Good Golly Garage Doors specializes in resolving high-tension spring failures efficiently, ensuring your system returns to safe operation without delay. We address the specific needs of homeowners in this region, where humidity and heat can accelerate metal fatigue in standard garage door components.

• Quick repair turnaround, often within the same day.
• Comprehensive safety inspections post-repair to ensure optimal operation.
• Transparent pricing with no hidden fees.

All repairs are carried out in accordance with local safety codes, complete with a satisfaction guarantee.

Solving Your Garage Door Spring Issues

The spring system is the counterbalance mechanism that allows a heavy garage door to be lifted manually or by an electric opener with ease. When a spring snaps, the door loses that lift assistance, often weighing several hundred pounds. Attempting to force the door open in this state can damage the opener, bend the tracks, or cause the cables to jump off the drums.

In the West Lake area, specific environmental factors contribute to spring failure. High humidity levels can lead to rust formation on steel coils, increasing friction and reducing the lifespan of the spring. Furthermore, the extreme temperature fluctuations between hot summers and cooler winters cause the metal to expand and contract, causing stress fractures over time. Most standard springs are rated for 10,000 cycles (one cycle is opening and closing the door once). Once that threshold is reached, the metal fatigues and breaks, often accompanied by a loud, gunshot-like noise.

Identifying the type of spring system your garage utilizes is the first step in the resolution process. Residential garage doors typically use one of two systems:

• Torsion Springs: These are mounted horizontally above the door opening on a metal shaft. They wind up and down to create torque that lifts the door. This is the most common system for modern, heavier doors.
• Extension Springs: These run parallel to the ceiling tracks on either side of the door. They expand and contract to generate the lifting force. These are often found on older doors or situations with low headroom.

Regardless of the system, a broken spring is a safety hazard. The stored tension in these components is immense. Professional intervention is required to safely unwind any remaining tension, remove the fractured components, and install a balanced replacement that matches the specific weight of your door panels — contact us today.

What We Offer – Quick, Reliable Repairs

We provide immediate response services because a broken garage door is a logistical emergency. Our service trucks are stocked with a wide array of high-grade steel springs in various wire gauges and lengths. This inventory management allows us to complete the majority of spring repairs in a single visit, eliminating the need for return trips or waiting on parts orders.

Our approach focuses on longevity and performance. We do not simply install the cheapest part available; we calculate the precise spring requirements based on your door’s height, weight, and track radius. Installing the wrong size spring—even if it technically fits—will result in an unbalanced door. An unbalanced door puts excessive strain on the electric opener, leading to premature motor failure and stripped gears.

Our standard repair offering includes:

• High-Cycle Spring Options: We offer springs rated for 25,000 to 50,000 cycles for homeowners who use their garage as the primary entry point. These oil-tempered or galvanized springs offer significantly longer life expectancy than builder-grade counterparts.
• Dual Spring Conversions: If your door currently operates on a single torsion spring, we can convert the system to a dual-spring setup. This provides redundancy; if one spring breaks, the second keeps the door from free-falling, offering a critical safety buffer.
• Complete System Tune-Up: Spring replacement is not done in isolation. We lubricate all moving parts, tighten hardware, and inspect bearings to ensure the new spring operates smoothly without unnecessary friction.

Our Repair Process: Fast and Thorough

Efficiency and safety dictate our workflow. We utilize a systematic approach to ensure that every replacement is performed correctly and that the door is left in a perfectly balanced state. We do not use guesswork; we use engineering calculations to match the lift power to the door weight.

• Assessment and Measurement: The technician begins by clamping the door securely to prevent movement. We then measure the existing spring’s wire size (using a micrometer), inside diameter, and overall length. We also weigh the door to verify that the previous spring was the correct size, as builders sometimes install undersized springs to save costs.
• Safe Tension Release: For torsion systems, we use winding bars to carefully unwind the tension from the unbroken spring (if it is a dual system) or remove the broken segments. For extension systems, we relieve tension from the safety cables and pulleys. This is the most dangerous part of the process and requires specific training to handle the kinetic energy release.
• Disassembly: The shaft is slid over to allow the removal of the old spring coils. We inspect the center bearing plate and the end bearing plates during this phase. If these bearings are worn or seized, they are replaced to prevent the new spring from binding.
• Installation: The new springs are slid onto the torsion tube. The stationary cones are bolted to the center bracket, and the winding cones are positioned for tensioning. We ensure the coils are oriented correctly (left-wound vs. right-wound) based on the side of the center bracket they occupy.
• Winding and Balancing: We wind the new springs to the calculated number of turns required for the door height. The technician then tests the balance by lifting the door manually. A properly balanced door should sit halfway open without falling or shooting up. If it drifts, we adjust the tension in quarter-turn increments until neutral buoyancy is achieved.
• Lubrication and Final Test: The coils are lubricated to reduce friction and noise. We reconnect the electric opener and run the door through several automatic cycles to verify the force settings and safety reverse mechanisms are functioning correctly.

Deciding Between Repair or Replacement

Homeowners often ask if a spring can be repaired or if it must be replaced. A broken spring cannot be welded or reconnected. The structural integrity of the metal has failed, and it must be replaced entirely. However, the broader question is whether to replace just the broken spring or upgrade the entire counterbalance system.

• Replace Both Springs: If your door has two springs and one breaks, it is standard industry practice and highly recommended to replace both. Both springs have been under the same tension for the same number of cycles. If one has failed due to fatigue, the second is likely near the end of its lifespan. Replacing both ensures the door remains balanced and saves you the cost of a second service call in the near future.
• Replace Cables: The lift cables work in tandem with the springs. Check the cables for fraying or rust. If the cables are damaged, they should be replaced simultaneously with the springs.
• Replace the Door: Spring failure does not typically require replacing the entire garage door unless the door sections themselves are damaged. If the door panels are cracked, water-logged (in the case of wood), or bent, a new door might be a better investment than repairing an old, heavy unit that strains the hardware.
• Conversion to Torsion: If you have an extension spring system, consider converting to a torsion spring system. Torsion systems are safer, quieter, and provide a smoother lift. This is a common upgrade for homeowners in West Lake looking to improve the reliability of their garage access.

Local Safety Standards and Compliance

Garage door repair involves working with systems under extreme tension, and local building standards in Texas prioritize safety and structural integrity. Good Golly Garage Doors adheres strictly to these requirements to protect your property and family.

In West Lake, where homes often feature heavy custom wood or carriage-house style doors, the spring system must be calibrated to handle significant weight loads. Undersized hardware on these heavy doors creates a severe safety risk. Our technicians verify that the torsion tube, drums, and cables are rated for the specific weight class of your door.

For extension spring systems, the installation of safety containment cables is non-negotiable. These steel cables run through the center of the spring. If the spring snaps, the safety cable prevents the loose coil from whipping around the garage, which could otherwise damage parked cars or injure bystanders. We inspect every extension system for these cables and install them if they are missing.

We also ensure compliance with fire safety and electrical codes regarding the opener’s connection to the door. The emergency release cord (the red handle) must be functional, allowing you to disconnect the door from the opener during a power outage—a relevant concern during severe weather events in the region.

Why Trust Us? Our Commitments to You

Selecting a service provider for garage door spring repair requires finding a partner who values technical precision and transparency. We do not use subcontractors; every technician is a trained employee who understands the mechanics of counterbalance systems. We arrive in clearly marked vehicles, fully equipped to handle the job immediately.

• Warranty Protection: We stand behind the quality of our parts. Our spring replacements come with a warranty that covers both the material and the labor. If a defect arises, we address it without hesitation.
• Upfront Pricing: You will receive a clear, itemized quote before any work begins. We explain the difference between standard and high-cycle springs so you can make an educated decision based on your budget and how long you plan to stay in the home.
• Safety Focused: We never bypass safety protocols to save time. We balance the door perfectly to ensure your electric opener is not overworked, extending the life of your entire garage door system.

A broken spring stops your day in its tracks, but the solution is a phone call away. We restore functionality, safety, and peace of mind with professional-grade hardware and expert installation.

Call us today to schedule your same-day garage door spring repair and get your door moving again.

Spring Component Replacement Completed for Lift Balance Recovery

Resolve operational instability with expert garage door spring repair in West Lake, TX, from Good Golly Garage Doors. We replace fatigued springs with high-cycle components selected for your door’s size and lift requirements. Each replacement is calibrated to restore controlled, uniform movement.

Spring Systems Rebuilt to Maintain Structural Load Balance