A Broken Garage Door Spring Has Trapped Your Vehicle

A broken or worn-out garage door spring can make your door unsafe, noisy, or completely inoperable. Good Golly Garage Doors provides expert garage door spring repair in Sun City West, AZ, quickly diagnosing and fixing torsion or extension springs to restore smooth, reliable operation. Our skilled technicians handle repairs safely and efficiently, ensuring your door opens and closes properly every time. Contact us today to schedule spring repair and keep your garage door functioning safely and efficiently.

What To Expect From Professional Spring Repair

When you require spring repair, you are looking for a specific outcome: a balanced door that opens smoothly without straining the operator. The service begins with a thorough assessment of your current counterbalance system. Technicians identify whether you utilize a torsion spring setup, which is mounted on a metal bar above the door opening, or extension springs, which run parallel to the track on either side.

The primary goal is to match the lift capacity of the new springs exactly to the weight of your garage door. Installing a spring that is too strong will make the door difficult to close and dangerous to operate, while a spring that is too weak will destroy your electric opener by forcing it to lift dead weight.

Service includes the removal of the fractured coil, the inspection of the cables (which often suffer damage when a spring breaks), and the installation of high-cycle replacement springs. Once installed, the technician winds the new springs to the specific tension required for your door height and weight. The final step involves a balance test where the door is disconnected from the opener and lifted manually. A properly repaired door should stay suspended halfway up the track without falling or shooting upward.

The Mechanics of Spring Failure and Replacement

Understanding why your spring failed helps you make better decisions about replacement options. Garage door springs are rated by “cycles.” One cycle is a full open-and-close motion. Builder-grade springs often last between 5,000 and 10,000 cycles. For a home that uses the garage as the front door, this might only translate to three to five years of use.

When a technician arrives to perform the replacement, the process follows a strict safety protocol to manage the massive potential energy stored in the system.

• Site Safety and Stabilization: The area is cleared, and the door is clamped to the track to prevent it from moving during the winding process. This is critical because if the door shifts while tension is being applied, it can cause catastrophic injury.
• Unwinding the Unbroken Spring: If you have a two-spring system and only one has snapped, the remaining intact spring still holds a massive amount of tension. This tension must be carefully released using winding bars before any hardware can be removed.
• Removal and Measurement: The old springs are removed from the center bracket and end bearing plates. The technician measures the wire size, inside diameter, and length of the coils. This data is used to fabricate or select the exact replacement needed for the door’s specific mass.
• Installation and Winding: The new springs are slid onto the torsion tube. The drums and cables are reset to ensure they are level. The new springs are then wound. This is the most dangerous part of the job, requiring physical strength and the correct leverage tools to apply torque to the steel.
• Lubrication and Testing: Once the tension is set, the coils are lubricated to reduce friction and noise. The door is run through multiple cycles to ensure the cables spool evenly on the drums and the door sits level on the floor.

Why High-Tension Repair Requires Certification

It is common for homeowners to look at a spring repair as a potential DIY project to save money, but this is statistically one of the most dangerous home repairs to attempt. The energy stored in a wound torsion spring is sufficient to break bones, sever fingers, or cause fatal head trauma if a winding bar slips or a casting fails.

The tools required for this job are specific. Professional technicians use hardened steel winding bars that fit perfectly into the winding cone holes. Makeshift tools, such as screwdrivers or socket extensions, often shatter under the torque or slip out, causing the spring to unwind instantaneously. This rapid release of energy can turn the tool into a projectile or cause the winding cone to spin uncontrollably.

Furthermore, correct cable setting is difficult without experience. If the cables are not set with equal tension on both sides while the springs are being wound, the door will rack (hang crookedly) in the opening. A racked door will jam in the tracks, potentially bending the vertical rails or popping the rollers out of their hinges. Professional repair ensures that the tension is balanced perfectly across the shaft, preserving the integrity of the entire door system.

Critical Decisions: Repair vs. Full System Replacement

When a spring breaks, you face a decision regarding the scope of the repair. While the immediate need is to replace the broken component, the condition of the surrounding hardware often dictates a more comprehensive approach to prevent a second service call next month.

• The Two-Spring Rule: Most double-car garage doors use two springs. If one breaks, the second one is likely near the end of its fatigue life as well. They were installed at the same time and have lifted the same weight for the same number of cycles. It is standard industry best practice to replace both springs simultaneously. Replacing only one leads to an unbalanced door and ensures the second spring will snap shortly after.
• Cycle Count Upgrade: You have the option to choose high-cycle springs. Standard springs may be rated for 10,000 cycles, but high-cycle springs utilize a larger wire diameter and longer length to provide 20,000 to 50,000 cycles. If you plan to stay in your home for many years, upgrading to high-cycle springs is a cost-effective investment that reduces long-term maintenance.
• Opener Health: If you attempted to open the door after the spring broke, you may have stripped the main gear in your electric opener. The technician will inspect the drive gear and sprocket. If the opener is old and suffered strain from the break, it may be more economical to replace the system alongside the springs rather than repairing an obsolete motor.
• Bearing and Roller Inspection: The end bearing plates support the torsion bar. If these bearings are seized or worn, they add friction that the new springs must overcome. Good Golly Garage Doors technicians inspect these wear parts to ensure the new springs operate efficiently.

Signs Your Springs Are About to Fail

While many breaks happen suddenly, your garage door often gives warning signs that the counterbalance system is weakening. Recognizing these symptoms allows you to schedule service before you are trapped.

• Elongation: If you have extension springs (the kind that stretch along the sides), look for gaps between the coils when the door is closed. If the coils are permanently stretched out, the steel has lost its elasticity and is close to failure.
• Squeaking and Groaning: Excessive noise that does not go away with lubrication often indicates that the metal is straining. A spring that is about to break may produce a distinctive chattering sound as the coils bind and release.
• Door Heaviness: Disconnect the opener (pull the red cord) and lift the door by hand. It should feel relatively light and stay in place when lifted halfway. If the door feels heavy or slams to the floor when you let go, the springs have lost their tension and are no longer balancing the weight properly.
• Jerky Movement: If the door moves in a jerky, stop-and-start motion, it may indicate that the springs are not providing consistent lift, or that one spring in a dual system has already failed, forcing the other to do all the work.

Differentiators in Service and Quality

The market for garage door repair is flooded with options, but the quality of parts and labor varies significantly. A correct repair focuses on the long-term reliability of the door, not just a quick fix.

• Precision Weighing: We do not guess the weight of your door. Technicians use scales or specific manufacturer charts to determine the exact inch-pounds of torque required. Installing a “close enough” spring results in a door that wears out your opener prematurely.
• Oil-Tempered vs. Galvanized: We prioritize the use of high-quality oil-tempered springs for their durability and resistance to losing tension. While galvanized springs look nicer initially, they often require more frequent re-winding as they relax over time. Oil-tempered steel retains its torque rating longer.
• Solid Warranty Protection: A spring repair is an investment in your home’s functionality. Services include warranties that cover both the material and the labor. If a replaced spring fails prematurely due to a defect, you are covered.
• Comprehensive Safety Inspection: Every spring appointment includes a safety check of the entire system, including sensors, track alignment, and hinge integrity. This ensures that the force of the new springs will not cause failure in other weakened components.

Restore Your Garage Access Today

A broken spring is more than an inconvenience; it is a security issue and a safety hazard. Your car is trapped, your home is vulnerable if the door cannot be closed completely, and the heavy door poses a risk to anyone trying to manipulate it manually. Do not attempt to wind torsion springs without professional training and tools.

Good Golly Garage Doors delivers the professional service required to get your garage door working smoothly again. The focus is on safety, precision, and high-cycle parts that extend the lifespan of your garage door system. Restore the safety and convenience of your home today. Contact us now to schedule your spring replacement service.